Welcome to the website where you can pass online the CES test on «6.0.16 STCW Engine Management Generic». Practice like this will help you as a marine specialist improve your knowledge with the help of online studying and appraisal practice. CES based on practical information and marine specialists experience.
CES tests developed for evaluating seaman basic knowledge by Seagull Company (rebranded as «OTG»), is an evaluating online-tool, used for revealing any professional preparation needed in specific fields of knowledge, defined by STCW.
Version: 6.0.16.
Test type: STCW.
Department: Engine.
Level: Management, Generic.
CES tests have proven themselves as good tools for the selection and recruitment process, as well as advancing the level of knowledge of the current officers and crew. Ocean Technologies Group use various subjects for question creation, which includes:
Crowd and Crisis Management;
Integrated Navigation System (INS);
Ballast water management;
Handling and Stowage;
Vessel operation management and safety;
Marine engineering;
Maintenance and repair, etc.
Current test contains Seagull CES questions in area «6.0.16 STCW Engine Management Generic». Those questions can be used for competence verification specialist capable of preventing accidental situations related with transporting safety, or also for self-examination.
«6.0.16 STCW Engine Management Generic» subject includes theoretical and practical information about advanced training for work on any type of vessel. The test is designed to provide maritime professionals with comprehensive knowledge and skills in managing shipboard engines and machinery. This course aligns with the International Maritime Organization‘s (IMO) Standards of Training, Certification and Watchkeeping (STCW) requirements, ensuring compliance with global maritime standards. Participants will learn to monitor, maintain and troubleshoot marine propulsion systems, auxiliary machinery and associated control systems effectively. The training emphasizes safe operational practices, including risk assessment, emergency response and preventive maintenance to ensure vessel reliability and crew safety. Practical exercises and simulations are integrated to enhance hands-on experience in engine room management under various operational conditions. Upon completion, learners will be equipped to handle routine and critical engine management tasks, contributing to the efficient and safe operation of maritime vessels. This test is essential for engineers and officers seeking to advance their careers and meet the STCW certification criteria for engine room responsibilities.
On this site Crew Evaluation System Test on the subject «6.0.16 STCW Engine Management Generic» contains 27 questions you need to answer with no possibility to go back to previous question. Therefore, we recommend carefully reading each question and making decision with no hurry. In case you have some difficulty answering, you have also possibility to request a hint.
Choose the regime, in which you want to pass CES test:
Training
Exam
Wild Mode
* Some questions may have more than 1 correct answer.
Which of the following requirements regarding life-buoys correspond to present regulations? (SOLAS III/7.1).
All the life-buoys shall be placed in holders with quick-release arrangement.
Not less than half the total number of lifebuoys shall be provided with self-ignighting lights.
At least four life-buoys on each side of the ship shall be fitted with buoyant lifelines.
At least one lifebuoy with self-activating smoke shall be placed within the vicinity of the stern.
Master of every ship must provide:
A link between the shipboard training officer and the company training officer ashore.
Facilities to conduct whenever required by the training officer.
The training during crews working hours only.
Proper rest to the crew after each training programme.
Which of the following is not a resistive sensor?
Thermistor.
Load resistor.
Photoresistor.
Strain gauge.
U-tube manometers are often used to measure differential pressure. Which of the listed pressures are U-tube manometers mostly used for?
Low differential pressures.
High differential pressures.
Cargo pressure.
Absolute zero pressure.
What is the minimum furnace temperature that must be reached during start up before waste material can be introduced into an incinerator?
850 °C.
1 500 °C.
2 000 °C.
2 500 °C.
In the circuit diagram shown the starter connects between which terminals?
1 and 2.
3 and 4.
5 and 6.
7 and 8.
What IMO conventions take care of the human safety at sea?
It is the SOLAS conventions that take care of the human safety at sea.
It is the MARPOL conventions that take care of the human safety at sea.
It is the STCW-78/95 that take care of the human safety at sea.
There are no conventions that take care of the human safety at sea.
What is usually the effect on G when the ship is damaged below the waterline, with water ingress?
It rises.
It first rises then lowers.
It lowers.
It is unchanged.
The torsion meter for the main propeller shaft is reading high. The torque is sensed using the angle of twist principle with two clamp rings attached to the shaft at a fixed distance, with stationary proximity switches for measuring the angle of twist and also shaft speed fixed to a rigid stool. What is the most likely cause of the high reading?
Circumferential slip of the after clamp ring in the opposite direction to shaft rotation.
Axial slip of one of the clamp rings to bring them closer together.
Circumferential slip of the forward clamp ring in the opposite direction to shaft rotation.
Axial slip of one of the clamp rings to move them further apart.
Give the meaning of the following symbol:
Survival craft portable radio.
Rocket parachute flares.
Survival craft distress pyrotechnic signals.
EPIRB.
The Training Manual shall contain instructions and information on the life-saving appliances and the best method of survival. The training manual shall contain detailed explanations of crew duties in relation to emergency situations. Which of the following tasks or duties shall be included in the manual according to present regulations?
The use of navigational equipment for survival crafts.
The use of the ship’s line throwing apparatus.
The use of escape routes and other escape methods.
The use of surface to air visual signals to be used by survivors.
The machinery detail plate is missing from a large electric motor and the weight is unknown. As part of a routine maintenance check the motor has to be lifted to access some other equipment. Which of the given options is the correct action that should be taken?
Try and lift it with the engine room crane as it is designed to lift the heaviest components in the engine.
Estimate the weight of the motor and select a chain block and strop with a safe working load of 1,5 times the calculated load.
Use the biggest chain blocks and strops available and carry out a trial lift.
As it is only a routine maintenance and not a breakdown then postpone the task until full details of the motor can be obtained.
When a pollution incident occurs there is a plan for actions to be undertaken. State which of following priority sequences to be considered:
Stop pumps – report – clean up?
Clean up – report – stop pumps?
Report – stop pumps – clean up?
Stop pumps – clean up – report?
How will continuous low load operation influence the time between overhauls, tbo, for the cylinder covers and associated valves of a 4-stroke diesel engine?
Increase the time between overhauls since the engine is not working as hard.
Increase the time between overhauls since fuel injectors work better at low load so combustion will be improved and the maintenance will be reduced.
Reduce the time between overhauls due to increased fouling.
No influence at all, the required overhauls are unaffected by operating load.
The coil of a 12V, 120mA dc relay must be connected across a 24V supply. What action should be taken?
Install a 100 ohm resistor in series with the coil.
Install a 100 ohm resistor in parallel with the coil.
Install a 100 k ohm resistor in series with the coil.
Install a 100 k ohm resistor in parallel with the coil.
“Protective discrimination” means the progressive grading of sizes or tripping times of:
440 V and 220 V transformers.
Line fuses and overcurrent relays.
Magnetic and thermal current transformers.
Generators and motors.
When bunkering through the port side of the bunker manifold what action should be taken with the valves on the starboard side of the manifold prior to bunkering operations commencing?
Blank flanges should be fitted to the closed starboard side manifold valves.
Just fit the blank flanges the it doesn’t matter if the valves are closed or not.
The blank flanges should be removed from the starboard side manifold valves to check for any leakage past the closed valves.
Just check that the valves are closed.
A diesel engine is operating with retarded fuel timing resulting in increased exhaust gas temperatures. How would you expect this to affect the turbocharger?
Increased turbocharger revolutions.
Decreased turbocharger revolutions.
The turbocharger would operate normally.
Reduced air and gas temperature after turbocharger.
Select the option which correctly completes the following statement. “Prior to allowing work to proceed in an onboard space testing of the atmosphere should be carried out”:
Only if the space has contained liquid oil at some point.
Only if the space has been used to carry any cargo or contains any cargo related equipment.
Only if the space has a watertight door or watertight access opening.
For any space with limited access or non-continuous ventilation or is suspected of having a hazardous atmosphere.
The main propulsion diesel engine is normally started by direct admission of compressed air. Which one of the following statements is correct?
A heavily leaking starting air valve may cause an explosion in the starting air pipe system.
If the starting air pressure is too low a pressurized oxygen bottle from the welding equipment can be used for an emergency start of the engine.
If the engine does not turn when the starting air is applied the turning gear can be used together with the starting air to start the engine.
The starting air admission should continue until the engine has fired.
Over a period of a few hours of operation the main diesel engine speed gradually falls off. From the options given what is the most likely cause of this fault?
Injection valve opening presure is too low.
Fouling of turbocharger intake filters.
Water in a cylinder.
Governor linkage broken.
A two step controller (open/close) has failed and the only available spare controller is a P+I controller. Select, from the options given, how the P+I controller could be set up to achieve approximate two step control.
Set the proportional band to minimum width and the integral action to maximum (repeats per minute).
Set the proportional band to maximum width and the integral action to minimum (repeats per minute).
Set the proportional band to minimum width and the integral action to minimum (repeats per minute).
Set the proportional band to maximum width and the integral action to maximum (repeats per minute).
What effect would turbulent fluid flow through a heat exchanger have on the efficiency of the heat transfer?
Turbulent fluid flow generally increases heat transfer efficiency.
Turbulent fluid flow generally reduces heat transfer efficiency.
Heat transfer efficiency is not affected by the type of fluid flow through the heat exchanger.
It cannot be determined since it is not possible to generate turbulent fluid flow through a heat exchanger.
When carrying out repair maintenance tasks involving hot work a hot work permit must be issued. Select the correct option from those given which completes the following statement. The permit for hot work:
Should only cover specific hot work tasks and be valid for a specified time period.
Is valid for completion of the specific hot work tasks irrespective of the time taken.
Should only cover specific hot work tasks, be valid for a specified time period and be issued by the person carrying out the work.
Can cover any additional hot work that arises during the completion of the task during the specified time period.
Some vessels have a central hydraulic system consisting of a number of hydraulic power packs for driving cargo pumps, deck machinery, ship’s cranes, etc. Which parameter is normally used to automatically bring the power packs on and off line to match operational demand?
Temperature of hydraulic fluid.
Number of consumers running (pumps, etc).
Percentage of available flow.
Percentage of maximum pressure being used.
Which of the following terms is used to describe a thermodynamic process in which no heat transfer into or out of the system occurs?
Polytropic.
Adiabatic.
Isochoric.
Isothermal.
The image shows an indicator diagram taken from a diesel engine cylinder. Which of the following options is the action most likely to identify the fault?
Check the exhaust valve.
Check if the fuel injection valve is partly blocked.
Check that the fuel temperature and viscosity are correct.
Check if the fuel pump injection is too early, or fuel pump lead is too great, for that cylinder.
Did you find mistake? Highlight and press CTRL+Enter
